Bathroom Fitting in Roxburghshire

Once you have your new bathroom installed, or perhaps you’re only replacing the old downlights, you’d probably want to know how to go about fitting your new bathroom downlights. If yes, then you’re not alone! This is a very common question amongst several homeowners and we wish to guide you through once and for all. However, it must be said that if you are not a competent DIYer or probably lack the confidence or skills to pull this off, then it’s advisable to hire a professional to get the best results and also save yourself some money and time.

Here are the list of the tools you’ll need to fit your bathroom downlights: Tape measure, chalk line or laser, pencil, pad saw, hand drill, hole saw and screw drivers.

✓ Measure the bathroom ceiling and mark out the central point of the light which will be where the downlights will be placed. Drill a small pilot hole here.

✓ Check above the ceiling to ensure that there’s no pipes, joists or wires in the way. It’s always a good practice to make sure that there’s sufficient room around where the downlight is to be installed in order to avoid placing it too close to a joist or any other obstacle. You should try as much as possible to maintain a 6 inch gap around the spot where the downlight is placed to make sure the fitting does not overheat.

✓ Use a hole saw or a plasterboard saw to make the cut out for the downlight. Check the downlight’s box for instruction on the size.

✓ Once you’ve been able to make a clean cut ceiling hole, pull through the wiring through the hole so that the downlight can be wired. Once done, then you can fit the downlight into the hole by holding the two springs back against the sides of the downlighter and push up into the hole.

Is your bathroom sink damaged or old and looking fragile? If yes, then you’re most likely interested in fitting a new one as soon as possible. So how do you go about the installation of a new bathroom sink? This is one of the most frequently asked questions when it comes to bathroom sinks and for a good reason. The fact is, if you’re DIY competent, then this is a task that shouldn’t give you too many hard times. However, if you’re without a proper training or experience, we’d recommend hiring the services of a plumber to guarantee the best results as save yourself some time and additional money which may result from costly errors. In this guide, you’ll learn the steps to bathroom sink installation.

✓ Tap preparation. Apply a small amount of plumber’s mate putty to the base of the taps to be installed.

✓ Install the taps. Identify the taps holes in the sink and squeeze the taps firmly in place, fit the washers and back nuts to the sink’s underside.

✓ Wipe off excess putty. Use a suitable tool to wipe off excess putty that has been pressed out by the tap.

✓ Install the wastage drain. Fit the wastage drain easily into the sink in such a way that the back and front (not side to side) is faced by the two wastage holes.

✓ Tighten the wastage pipe. Squeeze the wastage pipe in, include the washer on the opposite side as well as the nut. Tighten properly with an adjustable spanner and wipe off excess put using a screwdriver or any suitable tool.

✓ Fit the sink to the wall. Put the bolts in position before hanging the sink. Once done, then bolt the sink to the wall and tighten the nut with an adjustable spanner.

✓ Ensure that it’s level with the help of a spirit level.

Fitting a new bathroom can be a strenuous and very complicated task which usually comes with serious financial implications. But even more importantly, you’re most likely going to be working tight to a time schedule. So you’d like to know how soon you can have your bathroom space back and ready to use. This mostly either because you’re really impatient to see how your new bathroom will turn out to be or because you do not really fancy using another bathroom for long pending the time your new bathroom is being fitted and we definitely do not blame you. Having your bathroom back new and sparkling can be the best feeling ever and all professionals seek to get the job done as soon as they possibly can.

Overall, one thing that everyone would need to consider is mainly setting realistic expectations. Giving an accurate time it’ll take to complete the installation of your bathroom is almost impossible as there are many factors that can play a huge role in that. These factors include the size of the project as well as the design’s complexities, materials to be used and any other special requirements in the project. As a result, while 5 days is the average number of days it’ll take for the professional installation of a new bathroom, this can vary depending on the size of your bathroom and more. And you would have guessed, a smaller bathroom will require less number days when compared to a bigger bathroom with the same design. Also, designs can go a long way to determine the duration of a bathroom installation project with complex ones requiring more days as compared to simpler designs.

Surprisingly, bathroom renovations usually involves a wide range of trades to complete. And to make sure the work is done to a standard accepted by building regulations, some of these trades is required to have some particular legal qualifications. Therefore, if you’re interested in getting a new bathroom project done, you’ll probably need to call in more than just your plumber.

Below are the different trades you may need to successfully install a new bathroom:

✓ Plumber - The plumber’s task would be to install the new bathroom’s pipework and reposition and fit the bathroom items as needed.

✓ Tiler - To remove old tiles ( if any), prepare and tile the walls and/or floor.

✓ Labourer - To detach the old suite, strip out old tiles as well as floor covering etc.

✓ Plasterer - To skim the ceiling or board out the walls before you tile or plaster.

✓ Joiner - To re-hinge doors or construct studwork. For instance, when including a new bathroom to a bedroom.

✓ Painter - To paint the newly skimmed ceiling with the help of anti mould bathroom.

✓ Electrician - To install underfloor heating, ceiling spotlights, an extractor fan or a shaver point.

✓ A builder - A general builder will be required if your new bathroom project requires any structural work to be carried out such as installing a new uPVC window, putting in an RSJ and lots more.

✓ A decorate - As the name suggests, the decorator can come in to make the bathroom look a lot more attractive and to finish the job.

And above all, to ensure proper coordination and success of the project, you’ll also need a person who’ll serve as the lynchpin in charge of the entire project.