Garage Door in Barking and Dagenham

Request Garage Door Prices in Barking and Dagenham

Home > Metal garage doors > Barking and Dagenham

Average Metal garage doors cost in Barking and Dagenham

The regular cost of Metal garage doors is £1500. Costs vary based on the materials and the business hired. The upper price range can be as high as £1725. The material costs are normally approximately £375

Average price per Metal garage doors job in 2021

Avg. price low

Avg. price low
£1,125

Avg. price

Avg. price
£1,500

Avg. price high

Avg. price high
£1,725

£1900

£1425

£950

£475

£0

Prices based on actual Metal garage doors costs for Barking and Dagenham, as reported by local Quotatis members.

Metal garage doors installation cost in 2021

Labour cost £1,050
Material cost £375
Waste removal £75
Time frame: 1-3 days

Metal garage doors searches in July 2021

Metal garage doors Projects in Barking and Dagenham in June 2021

0

Requests for quotations in Barking and Dagenham in June 2021

0

Requests for Metal garage doors quotations in Barking and Dagenham in June 2021. 0% change from May 2021.

70

Requests for Metal garage doors quotations in London County in June 2021. -22% change from May 2021.

Source: Numbers calculated based on the search volumes in major search engines

Metal garage doors searches in cities and towns near Barking and Dagenham June 2021

4

Requests for quotations in Dagenham in June 2021

2

Requests for quotations in Romford in June 2021

2

Requests for quotations in Hornchurch in June 2021

2

Requests for quotations in Grays in June 2021

2

Requests for quotations in Upminster in June 2021

Barking and Dagenham

The London Borough of Barking and Dagenham is a London borough in East London, England. It lies around 9 miles (14.4 km) east of Central London. The borough was formed in 1965 by the London Government Act 1963 as the London Borough of Barking. The constituent areas were virtually all of the Municipal Borough of Barking as well as the largest part of the Municipal Borough of Dagenham, the former location of which was transferred to Greater London from Essex. It's an Outer London borough and the south is inside the London Riverside portion of the Thames Gateway, which is an location designated as a national priority for urban regeneration. It covers a total area of 13.93 square miles. According to the 2011 census, the area has a population of about 198294, the majority of which reside inside the Becontree estate. A lot of the housing within the borough was constructed by the London County Council through the interwar period of 1921-1939. Major settlement of the region, largely escaping slum conditions in the East End of London, occurred throughout this time when the new motor and chemical industries, including the Ford Motor Company plant at Dagenham were set up. Since the decline of those industries in the 1980s, employment has shifted much more towards service sector jobs. Much of the borough is within the London Riverside section of the Thames Gateway zone and it is the site of considerable house building and other development. The local authority is Barking and Dagenham London Borough Council. Barking and Dagenham was one of six London boroughs to host the 2012 Summer Olympics. For all your house upgrades, be sure that you utilise trustworthy experts in Barking and Dagenham to ensure that you get the best quality.

Looking for Metal garage doors in Barking and Dagenham?

Get free quotes from local garage door installers

Get free quotes

Metal garage doors pros in Barking and Dagenham

EVEREST LTD

49 review(s)
Based: in Potters bar, EN6 4SG

Everest windows are designed to beautifully complement your home and style, improving how pleasant, comfortable & secure your home is, whilst adding to its value & energy efficiency. Whether it’s uPVC, aluminium or timber, double or triple glazing,...

Latest review

James P., SP5
4

Windows | uPVC in Salisbury

very good

Similar Customer Enquiries for Metal garage doors in Barking and Dagenham

20 Sep

Doors | Garage

Romford - RM5

Enquiry from: SImon B

Start Date: Immediate

my garage door has got stuck and will not open from the outside. i want to replace it with one that i can automatically open from my car. preferably roll type rather than swing type. door size is 212c...

Post a similar request >

13 Sep

Doors | Garage

Romford - RM5

Enquiry from: Chris B

Start Date: Immediate

remove old garage door and install new electric roller door are you the property owner: owner of the property do you require an up and over garage door: yes are you looking to change other doors in yo...

Post a similar request >

10 Aug

Doors | Garage

Hornchurch - RM12

Enquiry from: Denise C

Start Date: Immediate

new garage doors or possible repair

Post a similar request >

31 Jul

Doors | Garage

Hornchurch - RM12

Enquiry from: Denise C

Start Date: Immediate

new garage doors or possible repair

Post a similar request >

25 May

Doors | Garage

Dagenham - RM10

Enquiry from: Francis N

Start Date: Immediate

Change the lock

Post a similar request >

04 Oct

Doors | Garage

Romford, Ilford - RM6

Enquiry from: Junel U

Start Date: Immediate

Garage door not closing Are you the property owner: Owner of the property Do you require an up and over garage door: No What material are you looking for: Metal Are you looking to change other doors ...

Post a similar request >

01 Sep

Doors | Garage

London - SW19

Enquiry from: Brian M

Start Date: 1 to 3 months

Automated single garage door Are you the property owner: Relative of Owner Do you require an up and over garage door: Yes What material are you looking for: uPVC Are you looking to change other doors ...

Post a similar request >

17 May

Doors | Garage

London - NW2

Enquiry from: Dhvanisha T

Start Date: Immediate

I need a quotation on maintenance for front double door gates which are wooden. One half of a door is 10 feet 8.5 inches in height and 6 feet in length. Are you the property owner: Owner of the proper...

Post a similar request >

16 Jul

Doors | Garage

London - W6

Enquiry from: Mrs M

Start Date: Immediate

The cable on our garage Marley auto door has snapped and it has become very difficult to open the garage straight up without scrapping the sides of the walls.

Post a similar request >

04 Jul

Doors | Garage

London - W6

Enquiry from: Martine B

Start Date: Immediate

I have an up and over Marley wooden chevron garage door where the cable down one side has snapped, preventing us from getting into the garage and would like to discuss repair options.

Post a similar request >

How it works

Tell us about your Metal garage doors project

Answer a few quick questions so we can match you with professionals who can help.

Find up to 4 Garage Door Installers in Barking and Dagenham

Get free, no-obligation quotes from 4 verified Garage Door Installers working in Barking and Dagenham.

Hire with confidence

Compare customer reviews, services and prices, and choose the right professional for you.

FAQs

How to insulate a garage door

There are several benefits that can be derived from insulating your garage door. Not only can it reduce your energy bills and protect your garage’s content from elements, but can also go a long way to increase the return on your property’s value, reduce noise, increase the garage door’s strength and deliver a more convenient garage and home. Insulating your garage is a task you can actually take on by yourself. However, if you lack proper training or experience, we’d recommend you leave it for a reliable professional who can ensure the project is done right, the first time - saving you both time and money. This guide will give you a good insight on how you can go about the project.

To insulate your garage, you’ll need a fibreglass insulation, garage door insulation, expanding foam, drywall, gloves and long sleeves, wood, sharp utility knife as well as a staple gun and staples. Now let’s take a look at the garage door insulation process!

lClear The Walls

• Remove the drywall (if present)

• Clean out the dirt and stud cavities.

• Wipe out any chemicals in the garage like gasoline.

lIdentify Gaps & Cracks In The Wall

• Shake your expanding foam vigorously for about a minute.

• Attach the straw to the can and use it to spray the wall openings.

• Fill the gaps until its 50% full

• Leave the foam to fill the openings completely in about 5 to 15 minutes. It should be hardened or completely cured within 6 to 8 hours.

lInstall Fibreglass Insulation

• Staple the insulation’s paper face to the side of the stud and not the face.

• Place a piece of wwod on the insulation’s top to act as a guide to properly cut the insulation to size.

• Cut the excess insulation with a utility knife.

• Tuck in the insulation to make for easier stapling.

• Staple the insulation down to the stud’s side.

lUse Drywall To Cover The Insulation

• Screw and glue the drywall to the stud.

• Do not leave the insulation’s paper exposed.

How to fit a garage door

Is your garage door a bit old and outdated? Are you planning to make some renovations? Or perhaps you just want a newer and more stylish garage door, that’s safer and easier to operate, installed. Fitting a garage door can be a bit tricky but it’s not as difficult as you might think. If you’re without proper training or experience, it’s advisable to get in touch with a reliable professional for help in order to guarantee the best results while also saving you both time and money. This guide offers you step by step instructions to assist you in the installation of a new door on our garage.

To get started, the obvious first step is to remove the old garage door. Carefully go through the manufacturer’s instructions to achieve this. Here, you’d basically have to unlatch the door, take apart the door’s panel and unscrew the tracks.

lMeasure, Fit The Hinges & Handles

• Take a measurement of the area in which the door will be fitted

• From the top of opening to ceiling should include a space of about 10 to 12.

• For the length of the garage, you should have the door’s height with about 18 or more space.

• Once done, attach stops to the sides of the opening

• Lay out the bottom piece of the door and include the weather stripping (if you deem fit) using the sawhorses.

lPut The Bottom Piece In Position

• Fit the bottom piece into door frame using a level

• Hit nails partway into each jamb

• Bend the nails slight to secure their position.

• Assemble the vertical, curved and horizontal pieces of the track using the manufacturer’s instruction

lFit The Remaining Panels

• Put the second panel on the first panel

• Use a hammer to hit nails into it

• Fit the hinges.

• Repeat the process for the number of panels required and achor individual piece into the door jamb.

lInstall Rollers

• Fit the rollers in the section’s supports

• Put the rollers in the assembled track and make sure they’re not pressed to tightly against the track to prevent friction.

lSecure Tracks & Fit The Springs

• Fit the curved and horizontal pieces

• Assemble the springs following the manufacturer’s instructions

• Ensure that the tracks are level and parallel by lifting the door to about half length

• Lift the door to cover the distance left and fit the springs to the pulley system

How much is a roller garage door?

This is a very sensible question to ask especially before making any decision. However, the answer is not always straightforward without conducting a proper survey of the site in question. In a stark contrast to many beliefs, a “standard garage door does not exist. And as a result of the great variety in specifications, there’s usually a need for garage door to be made to order.

Roller garage door are gradually becoming more and more accepted by homeowners across the country and reasonably so. The fact is, they’re the only type of garage door that features an electric motor as a standard rather than an optional extra. Therefore, if you’re considering the installation of a new garage door and wish to know more about the cost of getting a roller garage door, we’ve got you fully covered!

One thing you should take note is that the prices can vary due to garage door manufactures, price increases as well as the size and type of the garage door you want installed. However, here are the mostly likely price ( including both VAT and installation) you’ll pay to get a roller garage door in the UK.

• For an insulated roller garage door with a single garage door size, the price will range between £1099 to £1800.

• For an insulated garage door with a double garage door size, the price will range between £1400 to £3000.

• For an electric and insulated roller shutter garage door with a single garage door size, the price ( without VAT & installation) will range between £250 to £300.

• For an electric and insulated roller shutter garage door with a double garage door size, the price ( without VAT & installation) will range between £350 to £400.

How much do replacement garage doors cost?

This is one of the most important factors to consider when considering the replacement of your old garage door. However, the replacement cost of a garage door relies on a number of factors such as the type of the preferred garage door, the size of the area in which the door will be installed and lots more. To get a more accurate estimate of the replacement cost you also have to consider the cost of removing the old garage door and the mechanism, the price of disposing the old garage door from the premise, the cost of installing a new sub frame and a new door panel, cost of the new operating mechanism and modern locking installation as well as the cost of purchasing and installing the new garage door. Here, we are only going to look at the purchase and installation cost of the new asset.

Today, there are a wide range of garage doors to choose from such as sectional, rollers, up and down, side sliding ( round the corner) and side hinged. They also come with varying materials which plays a significant role in the cost of the item such as steel, timber, aluminium, PVC and more. Furthermore, several garage doors include the option of being controlled electronically.

Generally, garage doors will cost between £300 to £5000, and include a price with the range of £150 to £1000 for the ones that can be operated electronically. With that in mind, the remaining cost would be that of the professional installer and that should be between £150 to £250 a person per day. For the labour, you can expect the installation of your new garage door to be completed within 3 to 6 hours (although an electric or specialist door may take longer installation time than the conventional or manual ones).

Placholder Image

Other Top Projects in Barking and Dagenham

Quotatis Customer Reviews

Overall rating:


Barking and Dagenham Metal garage doors installers are rated 4 out of 5 based on 1 reviews of 26 pros.
The Quotatis rating and review is an overall rating based on verified reviews and feedback from the customers with Metal garage doors projects that have been connected with Metal garage doors pros to help them. All Metal garage doors contractors All Barking and Dagenham Metal garage doors contractors

Need more help?

5 Ways to Give Your Front Door a New Lease of Life Published: 18/03/2017 As it’s one of the first things that people see when they come to your home, your front door is worth investing in. A beautiful front door can create a great first impression to visitors and make you feel happy to be home. As an external part of your home, your front door can deteriorate […] Read this article
Should my Burglar Alarm go off during Power Cuts? Published: 18/10/2016 You might be wondering whether your burglar alarm will still protect your home in a power cut. What if you’re on holiday and the power goes out, meaning your home is subject to unwanted visitors? Well we’ve got the answers here. The short answer: no. Your burglar alarm really shouldn’t go off during a power […] Read this article
4 Signs it’s Time to Buy a Composite Front Door Published: 30/08/2016 How long have you had your front door? If you can’t remember, it’s probably time you changed it. And when you do, it’s worth considering a composite front door. Composite front doors are made from a range of materials. They are made up of uPVC, wood, insulating foam and glass reinforced plastic (GRP). This combination […] Read this article

Are you a garage door installer in Barking and Dagenham?

We can help you get more Metal garage doors work and boost your business.

Join today