Stud Wall/Plasterboarding in Alcester

Compare Stud Wall/Plasterboarding Prices in Alcester

Home > Plastering & Ceilings Projects > Plasterboard dry lining > Alcester

Stud Wall/Plasterboarding in Alcester

Internal or partition walls can be relocated or knocked down in your home, which can adjust the area layout and establish a more substantial open plan room design for a big living area or a kitchen diner. When moving or knocking through internal walls, it's important to understand both the kind of internal wall that it is, and whether or not it's a load bearing wall. Internal walls might be brick or block partitions, timber stud partitions, or even prefabricated wall panels. There are no shortcuts when it comes to ascertaining whether a wall is load bearing or not, it is advisable to engage the services of a structural engineer if you are unsure or are not able to view original plans for your premises. Load bearing walls can be relocated, but this may also be more expensive and involves installing additional load bearing solution, such as steel lintels. Moving or knocking through internal walls will often require demolition of the pre-existing wall, replacing or repairing the new walls, replastering and moving electrics. It may additionally demand adjustments to the floor, as occasionally the floors between rooms may not be entirely level, and knocking through interior walls can expose this. Generally moving interior walls will not require planning permission, but you'll need to adhere to building regulations for insulation and sound proofing. Consulting a structural engineer will ensure that any interior wall changes that you plan on doing will keep your house structurally sound.

Average Plasterboard dry lining cost in Alcester

The average cost of Plasterboard dry lining is £850. Costs vary based upon the materials and the tradesman hired. The upper price range can be as high as £977.5. The material costs are in most cases around £212.5

Average price per Plasterboard dry lining job in 2024

Avg. price low

Avg. price low
£638

Avg. price

Avg. price
£850

Avg. price high

Avg. price high
£978

£1100

£825

£550

£275

£0

Prices based on actual Plasterboard dry lining costs for Alcester, as reported by local Quotatis members.

Plasterboard dry lining installation cost in Alcester 2024

Labour cost £595
Material cost £213
Waste removal £43
Time frame: 1-2 days

Plasterboard dry lining searches in March 2024

Plasterboard dry lining Projects in Alcester in February 2024

548

Requests for quotations in Alcester in February 2024

0

Requests for Plasterboard dry lining quotations in Alcester in February 2024. 0% change from January 2024.

0

Requests for Plasterboard dry lining quotations in Warwickshire in February 2024. 0% change from January 2024.

Source: Numbers calculated based on the search volumes in major search engines

Plasterboard dry lining searches in cities and towns near Alcester February 2024

Alcester

Alcester is a market community as well as civil church of Roman origin at the junction of the River Alne and River Arrow in Warwickshire, England, around 8 miles (13 km) west of Stratford-upon-Avon, as well as 8 miles south of Redditch, near to the Worcestershire boundary. The 2011 demographics tape-recorded a population of 6,273. Today the town features style from the Medieval, Tudor, Georgian, Victorian as well as 20th century. The earliest house seems The Old Malthouse at the corner of Church Street and Malt Mill Lane, which probably dates from regarding 1500. The clock on St Nicholas Church (Quality 2 *) remains in an unusual setting on the south-west corner of the 14th-century tower, making it noticeable from the High Street. The church additionally houses the burial place of Fulke Greville, grandfather of Fulke Greville, 1st Baron Brooke. The church's Georgian nave with Doric columns and plastered ceiling is thought to have actually been designed by Francis Smith of Warwick, manager of its restore by Woodward brothers of Chipping Camden in 1729.

Looking for Plasterboard dry lining in Alcester?

Get free quotes from local builders

Get free quotes

How it works

Tell us about your Plasterboard dry lining project

Answer a few quick questions so we can match you with professionals who can help.

Find up to 4 Builders in Alcester

Get free, no-obligation quotes from 4 verified Builders working in Alcester.

Hire with confidence

Compare customer reviews, services and prices, and choose the right professional for you.

FAQs

How to plasterboard a brick wall?

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How to cut plasterboard?

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

How to fit plasterboard?

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

How to dot and dab plasterboard?

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Placholder Image

Other Top Projects in Alcester

Quotatis Customer Reviews

Overall rating:


Alcester Plasterboard dry lining installers are rated 0 out of 5 based on 0 reviews of 45 pros.
The Quotatis rating and review is an overall rating based on verified reviews and feedback from the customers with Plasterboard dry lining projects that have been connected with Plasterboard dry lining pros to help them. All Plasterboard dry lining contractors All Alcester Plasterboard dry lining contractors

Need more help?

What’s the Difference Between Plastering and Skimming? Published: 12/07/2017 You’ve probably heard people saying that they want their walls plastering. However, have you heard the less common term that they require skimming? We’re going to bust the misconceptions about the difference between these 2 terms. Plastering Contrary to popular belief, plastering is the term offered to the whole trade. This means that skimming is […] Read this article
3 Tips to Help You Maintain Your Plaster Published: 01/03/2017 If plasterboard is installed properly, it can last for a long time. But even top quality plaster walls will get damaged or wear out over time. You can increase how long your plasterboard lasts by taking steps to maintain it. Looking after your plaster walls can be easy and doesn’t require any specialist skills. Read […] Read this article
8 Things you Should Ask your Plasterer Published: 24/11/2016 What should you ask your plasterer to ensure that they’re an expert in their field? The plastering trade is a complicated one, so it’s always best to get a qualified professional to do plastering for you. Here are 8 things that you should ask your plasterer. If they’re good enough, they should be able to […] Read this article

Are you a builder in Alcester?

We can help you get more Plasterboard dry lining work and boost your business.

Join today