Stud Wall/Plasterboarding in Lymm

Request Stud Wall/Plasterboarding Prices in Lymm

Home > Plastering & Ceilings Projects > Plasterboard dry lining > Lymm

Stud Wall/Plasterboarding in Lymm

Internal or partition walls can be relocated or knocked through in your house, which can change the area layout and establish a substantial open plan room design for a ample living space or a kitchen diner. When moving or knocking through internal walls, it's important to understand both the type of internal wall that it is, and whether it's a load bearing wall. Internal walls may be brick or block partitions, timber stud partitions, or even prefabricated wall panels. There are no shortcuts when it comes to ascertaining whether a wall is load bearing or not, it's always worth engaging the services of a structural engineer if you are unsure or are not able to view original plans for your premises. Load bearing walls can be moved, but this may also be more expensive and involves using additional load bearing solution, such as steel lintels. Moving or knocking through internal walls will often require demolition of the existing wall, rebuilding or repairing the new walls, replastering and moving electrics. It may also necessitate changes to the floor, as in some cases the floors between rooms may not be completely level, and knocking through interior walls can expose this. Generally moving interior walls won't require planning permission, but you'll need to comply with building regulations for insulation and sound proofing. Consulting with a structural engineer will ensure that any interior wall changes that you intend on doing will keep your property structurally sound.

Average Plasterboard dry lining cost in Lymm

The average cost of Plasterboard dry lining is £850. Costs vary based upon the materials and the tradesman hired. The upper price range can be as high as £977.5. The material costs are in most cases around £212.5

Average price per Plasterboard dry lining job in 2024

Avg. price low

Avg. price low
£638

Avg. price

Avg. price
£850

Avg. price high

Avg. price high
£978

£1100

£825

£550

£275

£0

Prices based on actual Plasterboard dry lining costs for Lymm, as reported by local Quotatis members.

Plasterboard dry lining installation cost in Lymm 2024

Labour cost £595
Material cost £213
Waste removal £43
Time frame: 1-2 days

Plasterboard dry lining searches in March 2024

Plasterboard dry lining Projects in Lymm in February 2024

352

Requests for quotations in Lymm in February 2024

0

Requests for Plasterboard dry lining quotations in Lymm in February 2024. 0% change from January 2024.

0

Requests for Plasterboard dry lining quotations in Cheshire in February 2024. 0% change from January 2024.

Source: Numbers calculated based on the search volumes in major search engines

Plasterboard dry lining searches in cities and towns near Lymm February 2024

Lymm

Lymm is a large village and civil parish in Warrington, Cheshire in England. Lymm was an urban district of Cheshire from 1894 to 1974. The civil parish of Lymm incorporates the hamlets of Booths Hill, Broomedge, Church Green, Deansgreen, Heatley, Heatley Heath, Little Heatley, Oughtrington, Reddish, Rushgreen and Statham. In accordance with the 2011 Census, the village has a permanent population of around 12350 people. Within this population, 49.1 per cent are male and 50.9 percent are female. Lymm village centre is a designated preservation area, significant for its historic buildings, both listed and unlisted. These feature the French-style terracotta previous town hall, which is currently unlisted, St. Peter's Church, Oughtrington Hall and Lodge, formerly owned by a cadet branch of the Leigh family and now Lymm High School, and Lymm Hall, a previous Domville family home. Foxley Hall, home to a cadet branch of the ancient Booth family, before ownership passed to the Carlisle family, is not remaining, but fustian cutting homes on Church Road and Arley Grove do live on. The Parish Church of St. Peter, Oughtrington is an example of Gothic Revival architecture. St. Mary's Church, Lymm, neighboring Lymm Dam was in a state of disrepair by the middle of the 1800s so the Leigh family commissioned the noted Newcastle architect John Dobson to renovate it. The 1521 tower was maintained and raised, but the demand for added stonework rendered the tower being reconstructed in 1887. Lymm Cross, typically identified just as 'the Cross', is a Grade I listed structure. A 24-hour webcam oversees the landmark. Extra web cams are tactically located around. For all of your home remodelings, make certain to find reliable experts in Lymm to make certain of quality.

Looking for Plasterboard dry lining in Lymm?

Get free quotes from local builders

Get free quotes

How it works

Tell us about your Plasterboard dry lining project

Answer a few quick questions so we can match you with professionals who can help.

Find up to 4 Builders in Lymm

Get free, no-obligation quotes from 4 verified Builders working in Lymm.

Hire with confidence

Compare customer reviews, services and prices, and choose the right professional for you.

FAQs

What is plasterboard?

What Is Plasterboard?

The plasterboard is unarguably one of the most common building materials across the globe. Sometimes referred to as gypsum board, gyprock, drywall or wall board, the plasterboard is mostly incorporated for ceiling cladding and interior walls in several homes and offices in recent times. However, despite its global acceptability, it’s a very misunderstood building material.

The plasterboard is manufactured using a gypsum core with a heavy paper covering both sides of the sheet. The measurement of a standard plasterboard sheet is a length of 2.4 metres in and a width of 1.2 metres, with a thickness of about 13mm. The board usually have either a bevelled or a bit flat edge. The bevelled edge makes it easy for the installers to use a plaster to smooth out the surface after nailing the sheets to walls and ceilings as well as taping the edges.

The plasterboard comes in different types. Although various manufacturers provide a unique name for their products, but they’re all included in one of the following categories:

• Water Resistant Plasterboard - This type of plasterboard are best suited to be used in water areas like bathroom, laundry rooms and kitchens.

• Acoustic Plasterboard - Due to its sounding proofing qualities, this type of plasterboard is preferred to be used in home theatres or noisy areas.

• Flexible Plasterboard - This is to be incorporated on curvy surfaces.

• Fire Resistant Plasterboard - Just like the name implies, this type of plasterboard is best suited for use in high fire hazard areas.

If you’re about to kick start some small renovations around your house or office, using a plasterboard to clad your walls is a very simple and worthwhile task. However, if you want to do major renovations or need to apply plasterboard to your ceiling, the best option would be to leave it to a seasoned professional.

How to plasterboard a wall?

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

How to plasterboard a brick wall?

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How to dot and dab plasterboard?

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Placholder Image

Other Top Projects in Lymm

Quotatis Customer Reviews

Overall rating:


Lymm Plasterboard dry lining installers are rated 4.3 out of 5 based on 2 reviews of 45 pros.
The Quotatis rating and review is an overall rating based on verified reviews and feedback from the customers with Plasterboard dry lining projects that have been connected with Plasterboard dry lining pros to help them. All Plasterboard dry lining contractors All Lymm Plasterboard dry lining contractors

Need more help?

What’s the Difference Between Plastering and Skimming? Published: 12/07/2017 You’ve probably heard people saying that they want their walls plastering. However, have you heard the less common term that they require skimming? We’re going to bust the misconceptions about the difference between these 2 terms. Plastering Contrary to popular belief, plastering is the term offered to the whole trade. This means that skimming is […] Read this article
3 Tips to Help You Maintain Your Plaster Published: 01/03/2017 If plasterboard is installed properly, it can last for a long time. But even top quality plaster walls will get damaged or wear out over time. You can increase how long your plasterboard lasts by taking steps to maintain it. Looking after your plaster walls can be easy and doesn’t require any specialist skills. Read […] Read this article
8 Things you Should Ask your Plasterer Published: 24/11/2016 What should you ask your plasterer to ensure that they’re an expert in their field? The plastering trade is a complicated one, so it’s always best to get a qualified professional to do plastering for you. Here are 8 things that you should ask your plasterer. If they’re good enough, they should be able to […] Read this article

Are you a builder in Lymm?

We can help you get more Plasterboard dry lining work and boost your business.

Join today