Stud Wall/Plasterboarding in Nottingham

Discover Stud Wall/Plasterboarding Prices in Nottingham

Home > Plastering & Ceilings Projects > Plasterboard dry lining > Nottingham

Stud Wall/Plasterboarding in Nottingham

Internal or partition walls can be relocated or knocked through in your property, which can modify the room design and establish a more substantial open plan room design for a good-sized living area or a kitchen diner. When relocating or knocking through interior walls, it's important to understand both the sort of internal wall that it is, and whether or not it's a load bearing wall. Internal walls might be brick or block partitions, timber stud partitions, or even prefabricated wall panels. There are no shortcuts when it comes to ascertaining whether a wall is load bearing or not, it is advisable to engage the services of a structural engineer if you are unsure or are not able to view original plans for your premises. Load bearing walls can be moved, but this will often be more costly and involves using additional load bearing solution, such as steel lintels. Moving or knocking through internal walls will usually require demolition of the existing wall, rebuilding or restoring the new walls, replastering and moving electrics. It may also necessitate alterations to the floor, as sometimes the floors between rooms are not completely level, and knocking through interior walls can reveal this. Generally moving internal walls will not require planning permission, but you'll need to conform to building regulations for insulation and sound proofing. Consulting with a structural engineer will ensure that any internal wall changes that you plan on doing will keep your premises structurally sound.

Average Plasterboard dry lining cost in Nottingham

The average cost of Plasterboard dry lining is £850. Costs vary based upon the materials and the tradesman hired. The upper price range can be as high as £977.5. The material costs are in most cases around £212.5

Average price per Plasterboard dry lining job in 2021

Avg. price low

Avg. price low
£638

Avg. price

Avg. price
£850

Avg. price high

Avg. price high
£978

£1100

£825

£550

£275

£0

Prices based on actual Plasterboard dry lining costs for Nottingham, as reported by local Quotatis members.

Plasterboard dry lining installation cost in Nottingham 2021

Labour cost £595
Material cost £213
Waste removal £43
Time frame: 1-2 days

Plasterboard dry lining searches in October 2021

Plasterboard dry lining Projects in Nottingham in September 2021

12,366

Requests for quotations in Nottingham in September 2021

0

Requests for Plasterboard dry lining quotations in Nottingham in September 2021. 0% change from August 2021.

0

Requests for Plasterboard dry lining quotations in Nottinghamshire in September 2021. 0% change from August 2021.

Source: Numbers calculated based on the search volumes in major search engines

Plasterboard dry lining searches in cities and towns near Nottingham September 2021

Nottingham

Nicknamed Queen of the Midlands, Nottingham houses in excess of 300,000 people, and is well-known by way of its connections to Robin Hood. Construction inside the city backtracks to 1100s and complex buildings are on display from the nineteenth century. The city is split, with Georgian and Victorian eras seen to the west and modern developments to the east. Homeowners and landlords from Newcastle need building maintenance work and our vetted installers deliver totally free rates.

Looking for Plasterboard dry lining in Nottingham?

Get free quotes from local builders

Get free quotes

Similar Customer Enquiries for Plasterboard dry lining in Nottingham

13 May

Interior work | Stud Walls

Nottingham - NG8

Enquiry from: Janet D

Start Date: Immediate

plasterboard and plastering are you the property owner: owner of the property property type: terrace how many different rooms are you looking to have wall work on: 1-2 rooms what level of service do ...

Post a similar request >

02 Jun

Interior work | Stud Walls

Derby - DE24

Enquiry from: Prem M

Start Date: Immediate

to convert mid terraced house ***dsit are you the property owner: owner of the property what level of service do you require: supply and plaster property type: terrace how many different rooms are yo...

Post a similar request >

How it works

Tell us about your Plasterboard dry lining project

Answer a few quick questions so we can match you with professionals who can help.

Find up to 4 Builders in Nottingham

Get free, no-obligation quotes from 4 verified Builders working in Nottingham.

Hire with confidence

Compare customer reviews, services and prices, and choose the right professional for you.

FAQs

What is plasterboard?

What Is Plasterboard?

The plasterboard is unarguably one of the most common building materials across the globe. Sometimes referred to as gypsum board, gyprock, drywall or wall board, the plasterboard is mostly incorporated for ceiling cladding and interior walls in several homes and offices in recent times. However, despite its global acceptability, it’s a very misunderstood building material.

The plasterboard is manufactured using a gypsum core with a heavy paper covering both sides of the sheet. The measurement of a standard plasterboard sheet is a length of 2.4 metres in and a width of 1.2 metres, with a thickness of about 13mm. The board usually have either a bevelled or a bit flat edge. The bevelled edge makes it easy for the installers to use a plaster to smooth out the surface after nailing the sheets to walls and ceilings as well as taping the edges.

The plasterboard comes in different types. Although various manufacturers provide a unique name for their products, but they’re all included in one of the following categories:

• Water Resistant Plasterboard - This type of plasterboard are best suited to be used in water areas like bathroom, laundry rooms and kitchens.

• Acoustic Plasterboard - Due to its sounding proofing qualities, this type of plasterboard is preferred to be used in home theatres or noisy areas.

• Flexible Plasterboard - This is to be incorporated on curvy surfaces.

• Fire Resistant Plasterboard - Just like the name implies, this type of plasterboard is best suited for use in high fire hazard areas.

If you’re about to kick start some small renovations around your house or office, using a plasterboard to clad your walls is a very simple and worthwhile task. However, if you want to do major renovations or need to apply plasterboard to your ceiling, the best option would be to leave it to a seasoned professional.

How to plasterboard a wall?

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

How to plasterboard a brick wall?

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

How much plasterboard do I need?

How Much Plasterboard Do I Need?

Although many people especially contractors have a tough time estimating the number of drywall or plasterboard needed to complete a project, it’s a rather simple task if all factors are taken into consideration. If you’re able to follow the same procedures taken by professionals to count dry wall sheets, you’ll be in the right direction. Let’s have a look at the procedures to follow!

lTake Square Footage Measurement

• Measure the square footage of the area where the plasterboard will be fitted.

• Multiply the height by the width of each wall or ceiling area.

• Add all quantities to obtain a total square-foot amount.

lCalculate Drywall Sheets

• To calculate the number of drywall or plasterboard sheet is very simple once you’ve gotten the total square footage.

• To get started, simply divide the total square footage of area by 32 (that’s if you are using a 4 by 8 sheets) or you can also make use of 48 to make the division (only if you’re making use of the 4 by 12 sheets).

• The answer you get after the division will give you the full number of plasterboard sheets that’s required to complete the project.

We’d recommend you include an extra 10 to 15 percent of whatever you calculate to take care of the possible odd cuts and wastages. This implies that if your total area is 1600 square feet while incorporating 4 by 8 sheets, simply divide 1600 by 32 which equals 50 sheets, now take 10% of 50 which equals 5, then add back the 5 extra to the 50 sheets earlier calculated to get 55 sheets. If you wish to estimate the cost, simply multiply the number of sheets gotten by the price per sheet. Do not forget to include delivery charges and local taxes.

Placholder Image

Other Top Projects in Nottingham

Quotatis Customer Reviews

Overall rating:


Nottingham Plasterboard dry lining installers are rated 4.5 out of 5 based on 2 reviews of 78 pros.
The Quotatis rating and review is an overall rating based on verified reviews and feedback from the customers with Plasterboard dry lining projects that have been connected with Plasterboard dry lining pros to help them. All Plasterboard dry lining contractors All Nottingham Plasterboard dry lining contractors

Need more help?

What’s the Difference Between Plastering and Skimming? Published: 12/07/2017 You’ve probably heard people saying that they want their walls plastering. However, have you heard the less common term that they require skimming? We’re going to bust the misconceptions about the difference between these 2 terms. Plastering Contrary to popular belief, plastering is the term offered to the whole trade. This means that skimming is […] Read this article
3 Tips to Help You Maintain Your Plaster Published: 01/03/2017 If plasterboard is installed properly, it can last for a long time. But even top quality plaster walls will get damaged or wear out over time. You can increase how long your plasterboard lasts by taking steps to maintain it. Looking after your plaster walls can be easy and doesn’t require any specialist skills. Read […] Read this article
8 Things you Should Ask your Plasterer Published: 24/11/2016 What should you ask your plasterer to ensure that they’re an expert in their field? The plastering trade is a complicated one, so it’s always best to get a qualified professional to do plastering for you. Here are 8 things that you should ask your plasterer. If they’re good enough, they should be able to […] Read this article

Are you a builder in Nottingham?

We can help you get more Plasterboard dry lining work and boost your business.

Join today