Find a Heating Engineer you can trust in Bristol.

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Do Electric Boilers Work?

Electric boiler are installed in residential, commercial and industrial properties to serve as a reliable source of heat. Unlike other types of boilers that depends on fossil fuel burning to be able to operate, electric boilers are fuelled by electrical energy which ultimately makes it more reliable and powerful compared to its counterparts. This heating option was basically provided for home or property owners who don’t have an access to the main gas supply.

So how does an electric boiler work? Basically, an electric boiler work by heating water. Once heated, the hot water supply is then distributed to various areas across the house or property. In order to achieve the best possible efficiency at the lowest possible costs, new model electric boilers are installed by licensed and professional boiler fitters with the help of a microchip control system. Meanwhile, the microchip control system functions to oversee the management of both temperature level as well as output.

Unlike other types of boilers such as a gas boiler, electric boilers only require minimal service. If you own a gas boiler, it’s crucial to ensure that it’s serviced every single year by a licensed and reliable professional that’s into boiler repair services. During the checks and maintenance services, the gas boilers would need to be checked for possible gas leaks, as well as ventilation poisoning and other problems.

Overall, electric boilers are considered to be one of the most environment-friendly heating system which is more affordable to install in your property than a gas boiler. It represents the most ideal option for homes with gas boiler issues as well as those that are not connected to the main gas supply. What’s more? Electric boilers are also one of the best options for wet central heating and under floor heating.

Can You Replace Storage Heaters With Electric Radiators?

The short answer to this question is yes. If your outdated storage heater is not heating your home the way it should, you’ll find a better replacement in electric radiators.

Being more modern and efficient, electric radiators offer a wide range of benefits which storage heaters can only dream of. Let’s have a look.

• Unlike storage heaters, electric radiators do not need to be charged up the night before which makes it totally controllable as you do not have to guess what your heating needs will turn out to be the next day.

• The above benefit leads to an even better one as the controllability quality of electric radiators makes them a lot more efficient than storage heaters. Electric radiators usually comes with programmable timers and thermostats which allows you to set various heating schedules for each of your rooms, meaning you’re only heating when and where its needed.

• Unlike some storage heaters, electric radiators do not cause wall blackening and also happen to more elegant and stylish.

• Electric radiators are not tough on allergies like storage heaters as they do not depend mainly on convection to heat

• Electric radiators also have an easy installation process with all you need to do to switch from storage heater to one being the removal of the former and inserting the radiators into the sockets.

However, if you want to make a switch to electric radiators, there’s the need to change to a standard electricity tariff from your economy tariff. And while the standard electricity tariff rates may be more expensive than the night time rate provided by Economy 7, the standard tariff rates are a bit cheaper than the daytime Economy rate. You’ll also get to use much less of electricity while also saving money on your heating bills and more.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

How Much Is A Gas Safety Certificate?

If you’re a landlord in the UK, then you’d know a gas safety certificate is a legal requirement. If yes, then you’d probably like to know how much it’ll cost to get a gas safety certificate so you can make plans on obtaining one for your property. In this article, you’ll find all you need to know about the amount you’re expected to pay for a gas safety certificate in the UK.

First and foremost, let’s look into the use of the certificate. Basically, a gas safety certificate is the legal inspection of your property’s gas appliances which would be done on an annual basis. Only an approved Gas Safe engineer is allowed to carry out this statutory check. Ultimately, if you own rental properties in the country, this is a requirement you can’t afford to overlook to ensure the safety of your tenants.

Furthermore, included in this inspection are each and every gas appliances, chimneys, pipework as well as flues in the property. In recent times, several individuals make use of fewer gas appliances which ultimately implies that they may only need the servicing of their gas fire. Once you’ve passed the inspection, you’ll be given your CP12 certificate which must be kept for a minimum of two years. A copy should also be provided to your tenants within 28 days of issue. So how much will it cost to get a gas safety certificate?

Depending on your location in the UK as well as the number of gas appliances incorporated, the average cost of a gas certificate will range between £60 to £90. The Gas Safe engineer will carry out the task as a fixed and statutory job.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.